Acro Seal-CFV is a high-performance, nano-enhanced, water-based sealer and water repellent designed specifically for outdoor canvas, fabric, vinyl, and similar synthetic surfaces. Engineered to provide exceptional protection, it safeguards against moisture intrusion, weathering, UV damage, staining, and chemical exposure. This eco-conscious solution extends the lifespan and appearance of awnings, tents, vinyl siding, signage, fencing, and other outdoor materials.

Key Features

• Provides long-lasting resistance to water, stains, and weathering
• Shields surfaces from rain, humidity, deicing salts, pool chemicals, and pollutants
• Superior defense against oil, grease, acids, and solvents
• Reduces UV degradation, aging, and discoloration
• Non-yellowing, UV stable, and dries clear with a non-slip finish
• Completely non-toxic, biodegradable, non-flammable, and VOC-compliant
• Safe for enclosed spaces; emits no harsh odors
• Can be applied in multiple coats; self-leveling and fast drying
• Helps retain material flexibility, appearance, and cleanliness
• Exceeds ASTM standards for water repellency and chemical resistance

Application Instructions

Surface Preparation

Before applying, ensure all surfaces are clean, dry, and free of dust, debris, oil, stains, or previous coatings. For older or soiled materials, pre-clean using Bio Safe-CFV. Scrub with a soft nylon brush and rinse thoroughly. Allow the surface to fully dry.

Mixing

Gently shake or stir the product for 3–5 minutes before use. Avoid vigorous mixing to prevent air bubble formation.

Application

Apply with a brush, roller, or sprayer. For porous surfaces, two coats are recommended. Allow the first coat to dry before applying the second. Avoid application below 40°F. Product is dry to the touch in approximately 2 hours. Initial cure occurs within 10–12 hours, with full curing completed in 24–48 hours.

Coverage (Estimates per Gallon)

• Canvas & Vinyl (Solid): 1st coat: 300–500 sq ft | 2nd coat: 600–800 sq ft
• Canvas & Vinyl (Porous): 1st coat: 250–400 sq ft | 2nd coat: 500–700 sq ft
• Fabric: 1st coat: 200–300 sq ft | 2nd coat: 500–700 sq ft

(Note: Newer materials may yield higher coverage.)

Clean-Up

Rinse application tools with soap and water immediately after use.

Storage & Safety

Store in a cool, dry place between 40°F and 100°F. Avoid freezing and direct sunlight. Shake gently before reuse if stored long-term (up to 12 months). Avoid contact with glass and metal surfaces—clean immediately if accidental overspray occurs.

Precautions:

Wear protective gloves when applying. Avoid skin and eye contact. Do not ingest. In case of contact, rinse thoroughly with water. Remove and wash any contaminated clothing before reuse.

Important: Always follow label instructions and consult with a supplier or dealer for specific guidance based on surface conditions or contaminants.

Acryl Seal 25 – WB is a high-performance, water-based waterproofing solution engineered to protect concrete and masonry surfaces from the damaging effects of moisture, weathering, and de-icing salts. Formulated with advanced chemistry, this breathable, non-flammable coating deeply penetrates to form a long-lasting, protective barrier—ideal for both interior and exterior use.

Designed for use on concrete decks, pavements, ramps, parking structures, and vertical or horizontal masonry, it effectively resists spalling, cracking, and surface degradation caused by harsh environments.

Key Benefits

• Water-based & VOC-compliant: Environmentally friendly and safe to use indoors or in enclosed spaces.
• Breathable film: Allows trapped moisture within the substrate to escape, preventing blistering or peeling.
• Non-flammable & odorless: Easy and safe to apply, even in areas with limited ventilation.
• Durable & long-lasting: Offers extended surface protection on both new and aged concrete.
• Tack-free, skid-resistant finish: Safe for foot and vehicle traffic without compromising appearance.
• Effective barrier: Guards against moisture intrusion, freeze-thaw damage, spalling, and the corrosive effects of road salts and chemicals.

Recommended Applications

• All types of concrete structures
• Concrete blocks and precast concrete
• Brick and stone masonry
• Parking garages and ramps
• Lane dividers and highway barriers
• Asphalt-coated surfaces
• Tight or enclosed construction areas

AFV Siding Cleaner is a powerful, eco-friendly cleaning solution specifically formulated to safely remove stubborn stains and organic buildup from aluminum, fiberglass, and vinyl siding. Designed for both manual and pressure washer applications, this product offers effective results without harming roofs, gutters, or landscaping when used as directed.

The formula combines biodegradable detergents with a synergized blend of lipase enzymes—specifically chosen for their ability to break down organic matter such as grime, mildew, and various natural stains. These enzymes continue to work after application, delivering ongoing surface cleaning without damaging siding materials.

Key Benefits

• Biodegradable & non-toxic: Safe for use around plants, pets, and exterior finishes
• Will not damage surfaces: Ideal for aluminum, vinyl, fiberglass, and surrounding components when properly diluted
• Enzyme-enhanced: Contains lipase organisms and specialized enzyme blends for deep organic stain removal
• Flexible application: Effective with both power washers and manual cleaning methods
• Immediate cleaning action: Quickly breaks down and lifts dirt, grease, and organic stains

Removes

• Dirt & grime
• Grass stains
• Pollution & rust stains
• Spider webs & insect droppings
• Pollen & bird droppings

Application Instructions

Manual Cleaning

• Pre-wet surface thoroughly with water.
• Apply diluted solution (1:5 for heavy stains or 1:10 for general cleaning) using a soft-bristle brush or sponge.
• Work in rows, starting from the bottom up to prevent streaking.
• Rinse each section before it dries using a garden hose.

Pressure Washer Cleaning

• Pre-wet surface.
• Spray diluted cleaner evenly. Avoid allowing it to dry on the surface.
• Let it sit for approximately 60 seconds.
• Rinse thoroughly using a pressure washer.
• Repeat if necessary for persistent stains.

Avoid abrasive scrubbers or cleaning hot siding in direct sunlight to reduce streaking or surface damage.

Storage & Handling

• Store in a cool, dry place out of direct sunlight.
• Keep from freezing and avoid exposure to temperatures above 100°F or below 40°F.
• Shake well before use if stored for extended periods.
• Use protective gloves for prolonged handling. Avoid contact with skin and eyes.

AFV Siding Cleaner offers an environmentally responsible way to maintain exterior surfaces while delivering professional-grade cleaning performance.

Anti-Graffiti Coating – WB is a water-based, VOC-compliant penetrating sealer engineered with advanced nano-fusion technology. It delivers long-lasting protection for concrete and other porous surfaces by forming a deep, breathable barrier that resists water, weathering, corrosion, and all forms of graffiti—including spray paint, markers, and ink.

This product is ideal for use on new or existing concrete and masonry structures, including parking decks, ramps, floors, walls, and even porous fiberglass. It dries tack-free, leaves no yellowing, and maintains the original look of the surface while providing superior protection indoors or outdoors.

Key Features

• Water-based and environmentally compliant (VOC-compliant)
• Skid-resistant and dries tack-free
• Non-yellowing and UV stable for long-term clarity
• Provides moisture protection and prevents concrete spalling
• Repels graffiti, including spray paint, markers, and inks
• Suitable for both interior and exterior use
• Offers long-lasting surface durability on new or aged concrete

Recommended Applications

• Broom-finished or smooth concrete
• Parking structures and lane dividers
• Precast concrete and concrete blocks
• Brick and natural stone
• Exposed aggregate
• Porous fiberglass

Surface Preparation

• New Concrete: Ensure the surface is fully cured, clean, dry, and free of dust, oil, tar, and debris. Complete all sealing, caulking, and patching before applying.
• Old Concrete: Remove contaminants such as dirt, oil, and loose debris. Repair and dry the surface thoroughly before application.

Application Guidelines

• Apply with a roller brush or low-pressure sprayer. Start with a fine mist and follow with an even coarse spray to ensure full coverage. On damaged or spalled areas, a second coarse application is recommended.
• For a wet-look, high-gloss finish on floors, apply three or more coats. Allow at least 4 hours of drying time between each coat for best results.

Estimated Coverage

• Coverage depends on surface texture and porosity:
• Smooth concrete: 200–250 sq ft per gallon
• Broom-finished concrete: 150–175 sq ft per gallon
• Concrete blocks: 75–100 sq ft per gallon
• Brick (red or white): 200–250 sq ft per gallon
• Exposed aggregate: 175–200 sq ft per gallon
• Fiberglass: 300–400 sq ft per gallon

Clean-Up

Clean equipment and tools with warm water and soap immediately after use.

Packaging & Availability

Available in 1-gallon and 5-gallon jugs, and 55-gallon pails. Shipped FOB from Kansas City, Kansas.

Limited Warranty

EST Inc. warrants only the purchase price of defective material due to lack of control over storage, handling, and application conditions.

Anti-Graffiti Coating – SB is a solvent-based, breathable sealer formulated for use on all types of vertical masonry surfaces, including concrete, brick, natural stone, concrete blocks, and exposed aggregate. It provides long-lasting surface protection against graffiti and environmental contaminants, allowing graffiti to be removed multiple times before a reapplication is necessary.

This product penetrates deeply and creates a durable barrier that resists spray paint, permanent markers, and other forms of vandalism. It is ideal for use in public-facing areas such as building exteriors, bridges, retaining walls, and other exposed surfaces.

Recommended Surfaces

Anti-Graffiti Coating – SB is suitable for use on concrete (both cast-in-place and precast), concrete block, brick of all types, natural stone, and exposed aggregate surfaces. It is intended for vertical applications only and is not to be used on horizontal surfaces or asphalt. This product should not be applied to glass and is not recommended for use when ambient or surface temperatures are at or below 40°F.

Surface Preparation

New masonry surfaces must be fully cured, dry, and free of all dust, oil, tar, and debris. For older masonry, ensure all contaminants are removed using a pressure washer or appropriate cleaning methods. Any joints, caulking, or patching work should be completed prior to coating. If graffiti is already present, it should be removed using a heavy-duty detergent or solvent cleaner. Always test on a small, inconspicuous area before full application. Protect and mask all non-masonry surfaces prior to spraying.

Application Instructions

Apply Anti-Graffiti Coating – SB using a low-pressure sprayer. Start with a fine mist to break the surface tension and aid in product penetration. Follow with a heavier spray to achieve full, even coverage. For porous surfaces, apply two coats for best protection, allowing four to five hours of drying time between coats. Avoid application during hot, direct sunlight to minimize surface streaking.

Coverage Rates

Coverage will vary depending on surface texture and porosity. On average, this product covers approximately 100 square feet per gallon on concrete, brick, exposed aggregate, natural stone, and precast concrete. For more porous substrates such as concrete block, coverage may be closer to 75 square feet per gallon.

Cleanup

All tools and equipment should be cleaned promptly after use with mineral spirits or xylene. Dispose of cleaning materials according to local environmental and safety regulations.

Important Notes

Do not use this product on glass surfaces. Always test surfaces for compatibility prior to full-scale application. The durability of the coating and its graffiti-resistant properties may vary depending on the type of cleaning methods and solvents used during graffiti removal. Reapply the coating as needed based on surface exposure and frequency of cleaning.

Aqua Seal-25 is a water-based, penetrating sealer enhanced with nano-technology, engineered to protect both new and aged surfaces from graffiti, moisture, and environmental wear. This advanced coating is designed for deep penetration into concrete, masonry, and porous fiberglass, forming a long-lasting barrier against paint, ink, de-icing salts, and surface spalling.

Ideal for decks, concrete floors, pavement, parking structures, ramps, walls, and vertical or horizontal concrete, Aqua Seal-25 maintains the integrity and appearance of treated surfaces while preserving breathability.

Key Features

• Water-based and VOC compliant
• UV stable and non-yellowing
• Safe for indoor and outdoor use
• Skid-resistant and dries tack-free
• Long-lasting protection on new or existing surfaces
• Repels graffiti, spray paint, ink, and permanent markers
• Helps prevent moisture intrusion and concrete spalling

Recommended Applications

Aqua Seal-25 is suitable for use on broom-finished or smooth concrete, precast panels, parking garages, concrete barriers, blocks, exposed aggregate, brick, natural stone, and porous fiberglass surfaces. It is appropriate for both horizontal and vertical surfaces.

Application Guidelines

Apply with a roller brush or low-pressure sprayer. Begin with a fine mist to break the surface tension, then follow with a more even, coarse spray. For areas with surface spalling, a second coat may be required. On floors, a high-gloss wet look may be achieved with three or more coats, allowing at least four hours of drying time between each.

Surfaces must be clean, dry, and free of dust, oil, tar, and debris before application. Ensure joint caulking or patching is complete prior to coating. Older concrete should be pressure-washed or cleaned thoroughly and patched as needed.

Coverage Information

Coverage will vary depending on the texture and porosity of the substrate. On average:

• Broom-finished concrete: 150 to 175 sq ft per gallon
• Smooth concrete: 200 to 250 sq ft per gallon
• Exposed aggregate: 175 to 200 sq ft per gallon
• Concrete blocks: 75 to 100 sq ft per gallon
• Brick (red or white): 200 to 250 sq ft per gallon
• Fiberglass: 300 to 400 sq ft per gallon

Clean Up

Clean tools and equipment with warm water and soap immediately after use.

Packaging

Available in 1-gallon, 5-gallon, and 55-gallon containers.

Availability

Shipped FOB from Olathe, Kansas.

Warranty Disclaimer

EST Inc. provides this product under a limited warranty restricted to the purchase price of the material. As we cannot control conditions of storage, handling, or usage, no other warranties—expressed or implied—are offered.

This industrial-grade remover is specifically formulated to eliminate tar, asphalt, oil stains, grease buildup, and black tire marks from various surfaces including brick, stone, concrete masonry, and metal. It is ideal for use in parking garages, parking lots, driveways, mechanic shops, airport runways, highways, and other areas where such contaminants are commonly found.

The product is designed to work in a two-step cleaning process. In Step One, apply the remover generously to the affected surface using a sprayer or brush. Allow the solution to sit for two to three minutes to loosen surface-level buildup. Reapply and agitate the area vigorously with a nylon or hard-bristle brush, then rinse thoroughly with water. Repeat the process as needed until all visible residues are eliminated. Take care to test surrounding surfaces before application and protect them from potential overspray.

Once surface contaminants are removed, Step Two involves using EST’s Heavy-Duty Concrete Cleaner to address deeper, embedded stains that have penetrated the substrate. This secondary cleaner lifts oil and grease that has soaked into the pores of concrete and masonry. Depending on the severity and age of the staining, two to three applications may be required for complete removal. For best results, consult the product label or technical data sheet for EST’s Heavy-Duty Concrete Cleaner.

On highly porous surfaces, a high-pressure rinse is recommended. For interior applications where power washing isn’t feasible, use a stiff brush and water to rinse and agitate the surface manually.

Enzymatic Cleaner Concentrate is a biodegradable and eco-friendly solution formulated for cleaning hard surfaces such as concrete masonry, tile, fiberglass, plastic, and natural stone. It is designed for dilution with water and can be applied easily via mopping, spraying, or wiping. Safe for daily use, this cleaner offers continuous, deep cleaning by going to work immediately—absorbing, emulsifying, and lifting soil and contaminants from a wide range of surfaces.

This advanced formulation includes a synergized blend of lipase-producing microorganisms that accelerate the degradation of organic matter commonly found on industrial and commercial surfaces. The enzymatic action hydrolyzes fats, oils, grease, proteins, and starches—making it highly effective against stains caused by food residue, wax, dye, inks, creosote, carbon buildup, and other stubborn organic soils.

Enzymatic Cleaner penetrates deeply to lift embedded grime, while remaining non-toxic, water-soluble, and safe for metals, plastics, rubber, and concrete. It contains rust inhibitors that make it suitable for cleaning sensitive metal surfaces without causing corrosion. In addition to being a powerful general-purpose cleaner, it also works effectively as a wax stripper, removing old wax layers without leaving behind a sticky or oily residue.

This cleaner is 100% fireproof, emits no hazardous fumes, and contains no harmful solvents such as naphtha, kerosene, or benzene—making it suitable for indoor use in kitchens, food-processing facilities, and other enclosed environments where safety is critical.

The product can be diluted at a ratio of 1 to 15 with water, providing strong cleaning performance while remaining cost-efficient. This economical formula helps reduce labor time, cuts down on product waste, and extends the life of equipment and surface finishes.

Application Directions

Before use, always test on a small section of the surface to ensure compatibility. Protect any nearby materials not intended to be cleaned.

For General Cleaning:

Spray the cleaner directly onto the affected area. Wait 15 to 20 seconds, then scrub gently with a soft nylon brush and rinse thoroughly. Repeat the process for persistent stains until fully removed.

For Exterior Cleaning:

Pre-wet the surface to be cleaned. Dilute the cleaner with 4 to 6 parts water, based on surface type and soil level, using dilution guidance from previous testing. Apply the solution with a soft nylon-fibered brush and allow it to dwell for 2 to 3 minutes. Do not allow the cleaner to dry on the surface. Rinse thoroughly using a hose or pressure washing equipment (at approximately 3 gallons per minute and 400–600 psi). To prevent streaking, always keep the lower sections of vertical surfaces wet during rinsing.

Bio Safe-CFV represents the next generation of surface restoration and protection technology. Formulated using cutting-edge nano-penetration chemistry and fused with eco-conscious biotechnology, this product contains no harmful acids, phosphates, or toxic solvents—making it both highly effective and environmentally responsible.

This specialized cleaner is engineered specifically for outdoor fabric and vinyl surfaces such as awnings, tents, shade sails, banners, and signs. It rapidly penetrates surface layers using microscopic nano molecules that break the surface tension and access embedded stains. Once inside the substrate, a biological cleaning agent activates—breaking down and lifting away organic and environmental buildup without damaging the material.

Bio Safe-CFV is ideal for removing stains caused by mold, mildew, algae, lichen, moss, and airborne pollutants. It not only cleans but also preserves surface integrity, helping prevent recurring stains caused by exposure to moisture and the elements.

Application Process

Pre-Inspection and Preparation:

Always begin by performing a spot test on a small area to determine optimal contact time, coverage rate, and surface compatibility. Protect all surrounding surfaces that are not intended to be treated. If overspray occurs, rinse off immediately with water.

Step-by-Step Instructions:

• Surface Pre-Wetting: Pre-wet the surface with clean water to reduce product evaporation and allow even coverage.
• Product Application : Apply Bio Safe-CFV undiluted using a brush, roller, pump sprayer, or low-pressure power sprayer. Dilution is not required.
• Contact Time : Allow the product to sit on the surface for approximately 10 to 12 minutes. Avoid letting it dry during this period.
• Agitation: For heavy mold and mildew buildup, pre-soak the surface thoroughly. Then scrub with a soft nylon or natural-bristle brush. Do not use wire brushes, as they may cause abrasion or surface damage.
• Rinsing : Rinse with clean water. For large surface areas, use a low-pressure power washer, ensuring that the pressure is adjusted to suit the sensitivity of the material. Always conduct a spot test before rinsing the full area. Scrubbing during rinsing is recommended for persistent staining.
• Repeat if Necessary : For stubborn or recurring stains, reapply the product and repeat the process. For optimal results, perform cleaning operations at ambient temperatures above 45°F.
• Surface Protection: To avoid harming nearby vegetation or unintended surfaces, use shields or barriers to control overspray. Rinse all non-target areas thoroughly if contact occurs.

No-Scrub / No-Rinse Application Option

For less severe staining or quick maintenance, Bio Safe-CFV can be used as a no-scrub solution. Using a pump-up sprayer, garden hose sprayer, or low-pressure applicator, apply generously over the entire surface. Allow the product to remain and air dry—no agitation or rinsing required.

The cleaning process activates through contact with environmental elements such as air and moisture, and visible results typically appear within an hour. Reapply if discoloration remains.

Annual Maintenance Program

To extend the cleanliness and aesthetic appearance of treated surfaces, a light spray application once a year is recommended. This preventative approach minimizes biological buildup and environmental staining. In cases of severe mold, mildew, or algae regrowth, revert to the full cleaning procedure for complete restoration.

Brick Clean 101 is a synthetic acid formulation designed as a safer, user-friendly alternative to traditional acids such as muriatic and hydrochloric acid. Engineered for professional masonry cleaning, this advanced formula delivers the strength of conventional acids with significantly reduced health, safety, and handling risks.

Ideal for removing construction debris, excess mortar, and job-site stains from a wide variety of brick and masonry surfaces, Brick Clean 101 is both effective and easier to manage—making it a go-to choice for contractors and facilities maintenance professionals.

Key Benefits

• Effectively removes excess mortar from dark and light-colored brick
• Synthetic acid chemistry is less corrosive and safer to handle
• Suitable for use on red, buff, high-density, and structural tile surfaces
• Designed for economical dilution without compromising strength
• Will not burn or discolor masonry
• Safe for use near aluminum trim and windows

Note: For light-colored bricks prone to discoloration (white, buff, magnesium, pink salmon), use EST Brick Clean – Vanadium, specially formulated to prevent vanadium (green), manganese (dark brown), and other metal-based stains.

Surface Compatibility & Dilution Guidelines

Dilute Brick Clean 101 with water based on the surface being cleaned. Always prepare a test panel to confirm results and optimal ratio.

• Red or high-density brick: 1 part Brick Clean to 5 parts water
• Buff or non-discoloration-prone brick: 1:5
• Light-colored brick: 1:5
• Structural tile, ceramic, or glazed surfaces: 1:8

Average coverage: 400 sq. ft. per gallon, depending on porosity and surface condition.

Application Instructions

Preparation

• Remove loose dirt, mud, and debris.
• Protect all non-masonry surfaces with plastic sheeting or masking tape.
• Avoid contact with surrounding landscaping, painted areas, fixtures, or metals not intended to be cleaned.

Exterior Cleaning

• Pre-Wet Surface : Soak the masonry thoroughly to reduce product absorption and minimize etching or streaking.
• Product Application : Apply the diluted solution using a masonry brush or low-pressure sprayer. Allow to sit for 2–3 minutes—do not let dry.
• Agitation : Scrape off excess mortar using a wooden or plastic scraper. Avoid metal tools that may scratch surfaces.
• Rinse: Rinse thoroughly using a pressure washer (400–600 PSI at 3 GPM) or with large amounts of clean water. Always work from top to bottom, keeping lower sections wet to avoid streaking.

Interior Cleaning

• Ensure adequate ventilation.
• Protect floors and interior fixtures (plumbing, switches, doorknobs, etc.) using poly film or masking material.
• Follow the same procedure as for exterior surfaces.
• If rinsing with a hose is not possible, use a sponge or wet brush. Rinse repeatedly.
• To neutralize residual cleaner, mix 2 oz. of household ammonia per 2 gallons of water and wipe the cleaned area.

Storage & Handling Guidelines

• Store in a cool, shaded area—away from direct sunlight, freezing conditions, or high heat (above 100 °F or below 40 °F).
• Keep container tightly closed when not in use.
• Always wear protective gloves (rubber, neoprene, or nitrile) and wash hands after use.
• Avoid contact with skin, eyes, and clothing. Do not ingest.
• Contaminated clothing should be washed before reuse.

First Aid Measures

• Eyes: Rinse immediately with clean water for at least 15 minutes. Seek medical attention if irritation persists.
• Skin: Wash thoroughly with water. Get medical help if symptoms persist.
• Ingestion: Do not induce vomiting. Seek medical attention immediately. If vomiting occurs, keep head below hips to prevent aspiration.

Conditions of Sale

This product must be used strictly in accordance with label instructions. The manufacturer is not responsible for improper application, weather-related effects, or use on unsuitable substrates. Buyer assumes all liability when instructions are not followed.